Added to cart successfully
🚀 Selamat datang di INERGEK! Kami menyediakan komponen teknik premium dengan dukungan 24/7. Pesan sekarang dan dapatkan DISKON 15% pada pembelian pertama Anda!
Pesanan Cepat Lacak Pesanan
Favorit
INERGEK
Search Products
Arahkan kursor untuk memperbesar
PN: SBRS-(4X)GR2000

4:1 shrink ratio Flame-Retardant, High Viscosity,Adhesive-Lined, Semi-rigid Polyolefin Heat Shrink Tubing

SBRS-(4X)GR2000 Flame-Retardant, High Viscosity,Adhesive-Lined, Semi-rigid Polyolefin Heat Shrink Tubing It consists of a double layer of cross-linked polyolefin and polyamide PA. Widely use

HARGA
Permintaan Penawaran
Silakan hubungi kami untuk rincian harga
Tindakan Cepat

SBRS-(4X)GR2000

Flame-Retardant, High Viscosity,Adhesive-Lined, Semi-rigid Polyolefin Heat Shrink Tubing

It consists of a double layer of cross-linked polyolefin and polyamide PA. Widely used in automotive wiring harness, electronic equipment wire connection and other sealed occasions.

It consists of a double layer of cross-linked polyolefin and polyamide PA. Widely used in automotive 

wiring harness, electronic equipment wire connection and other sealed occasions.

23   SBRS-(4X)GR1000.png


Features

● 4:1 shrink ratio to cover varying splice configurations and substrate profiles.

● Flame-retardant and mechanically tough, the tubing provides strain relief and abrasion protection 

   of wire splices, terminals, and other components.

● Thick adhesive liner forms an effective barrier against fluids and moisture penetration.

● Minimum shrink temperature: 110°C [230°F].

● Continuous operating temperature: -40°C to 130°C [-40°F to 266°F].

● Fully shrink temperature:135℃[275°F].

● Can be applied for multiple strands wires sealing.


​Technical Data

PropertyTest MethodStandard
Tensile Strength(MPa)ASTM D2671≥10.3
Elongation(%)ASTM D2671≥250
Heat Shock 4 hours at 250±3℃ASTM D2671No dropping, flowing or cracking
​FlammabilityASTM D 2671 BSelf-extinguishing within 30 seconds
2% Secant Modulus*(expanded, MPa)ASTM D2671​≥173
Dieletric strength(kV/mm)IEC 243≥15
Volume resistivity(Ω.cm)ASTM D876≥1X1013
* Calculate based on wall thickness of jacket only.

Adhesive

PropertyTest MethodStandard
Water AbsorptionASTM D570<0.2%
Sofening Point (℃) ASTM E28100±5
Strength of peeling(PE) ASTM D 1000120N/25mm
Strength of peeling(AL)ASTM D 100080N/25mm


Specification Table

Dimensions

SizeExpandedAfter Recovery
mm

Inner Diameter

Min(mm)

Inner Diameter

Max(mm)

Total Wall 

Thickness(mm)

Adhesive 

Thickness(mm)

Φ5.72

5.72

1.27

1.42

0.65

Φ7.44

7.44

1.65

1.76

0.90

Φ10.85

10.85

2.41

2.10

1.20

​​Φ17.78

17.78

4.45

2.41

1.37

*Wall thickness will be less if tubing recovery is restricted during shrinkage.